Master Notes ----------------- ------------------------------------------------------------------------------------ ------------------------------------------------------------------------------------ FastIron FLS 648 - same as FGS code ------------------------------------------------------------------------------------ ------------------------------------------------------------------------------------ #erase flash primary copy tftp flash 192.168.0.24 fgz05000.bin bootrom copy tftp flash 192.168.0.24 FGSL07202d.bin primary copy tftp flash 192.168.0.24 FGS07202d.bin secondary (config)#boot system flash secondary - option to load from Layer 2 code ------------------------------------------------------------------------------------ ------------------------------------------------------------------------------------ Fastiron SuperX- same as FESX code ------------------------------------------------------------------------------------ ------------------------------------------------------------------------------------ ------------------------------------------------------------------------------------ ------------------------------------------------------------------------------------ Cisco 1800, 2600 ------------------------------------------------------------------------------------ ------------------------------------------------------------------------------------ rommon>confreg 0x2142 rommon>reset (config)#config-register 0x2102 #copy run start ------------------------------------------------------------------------------------ ------------------------------------------------------------------------------------ Cisco Catalyst 3550 ------------------------------------------------------------------------------------ ------------------------------------------------------------------------------------ Recover from missing image: switch: set BAUD 57600 copy xmodem: flash:c3550-i5k2l2q3-mz.121-13.EA1a.bin ------------------------------------------------------------------------------------ ------------------------------------------------------------------------------------ Cisco 7206 VXR ------------------------------------------------------------------------------------ ------------------------------------------------------------------------------------ Set the boot variable: #show bootvar #(config)boot bootldr slot0:"FLASH FILE NAME" --------------------------------------------------------------------------------- --------------------------------------------------------------------------------- Cisco 7200 VXR --------------------------------------------------------------------------------- --------------------------------------------------------------------------------- #show controllers T1 --------------------------------------------------------------------------------- --------------------------------------------------------------------------------- Cisco 4948-10GE --------------------------------------------------------------------------------- --------------------------------------------------------------------------------- #sho diagnostic result module 1 d --------------------------------------------------------------------------------- --------------------------------------------------------------------------------- Cisco 2800 --------------------------------------------------------------------------------- --------------------------------------------------------------------------------- Router(config)#boot system flash:c2800nm-spservicesk9-mz.124-7.bin ---------------------------------------------------------------------------------- ---------------------------------------------------------------------------------- Cisco vlan commands ---------------------------------------------------------------------------------- ---------------------------------------------------------------------------------- #Interface fastethernet 2/0 #Switchport access vlan 10 #Show interfaces switchport ---------------------------------------------------------------------------------- ---------------------------------------------------------------------------------- EdgeIron 2402CF ---------------------------------------------------------------------------------- ------------------------------------------------------------------------------------ Console#copy tftp file ------------------------------------------------------------------------------------ ------------------------------------------------------------------------------------ Cisco 4500 with WS-X4515 Supervisor Engine IV ------------------------------------------------------------------------------------ ------------------------------------------------------------------------------------ Switch#show bootvar Switch#configure t (config)#no boot system flash bootflash:cat4000-is-mz.121-8a.Ew (config)#boot system flash bootflash:cat4000-is-mz.121-11b.EW #write memory ------------------------------------------------------------------------------------ ------------------------------------------------------------------------------------ Cisco 3750G ------------------------------------------------------------------------------------ ------------------------------------------------------------------------------------ #show controllers ethernet-controller gi0/21 phy #show diagnostic result switch 2 test all #show post ------------------------------------------------------------------------------------ ------------------------------------------------------------------------------------ Cisco WS-SUP720 ------------------------------------------------------------------------------------ ------------------------------------------------------------------------------------ rommon 1 > set rommmon 2 > BOOT=bootdisk0:s72033-advipservicesk9_wan-vz.122-18.SXF14.bin rommon 4 > sync Wait for change of ownership before performing "break sequence" rommon>confreg 0x2142 rommon>boot bootflash:s72033-psv-mz.122-18.SXD7b.bin #show bootvar #copy start running #config-register 0x2102 #show environment #show environment status #show diagnostics power-on #show interface interface-id status rommon>dir sup-bootdisk: CatOS - #set module power up module_number CatIOS -#power enable module slot ----------------------------- Recover from missing image ------------------------------ >set >unset >set interface fa1 14.18.2.234 255.255.255.0 >set ip route default 14.18.2.21 >ping 172.18.125.3 >boot tftp://172.18.125.3/cat4000-is-mz.121-11b.EW -------------------------------------------------------------------------------------- -------------------------------------------------------------------------------------- Brocade MLX4-AC -------------------------------------------------------------------------------------- -------------------------------------------------------------------------------------- Password recovery ------------------ press b no password boot system flash primary after it boots: erase start reload press Y --------------------------------------------------- Software Upgrade ------------------------------------------------- delete ___mbridge.old #int man1 ip address 192.168.0.80/24 copy tftp image 192.168.0.42 xm05100d.bin secondary del copy tftp flash 192.168.0.42 xmr05100d.bin primary copy tftp flash 192.168.0.42 xmb05100a.bin monitor copy tftp flash 192.168.0.42 xmprm05100a.bin boot copy tftp lp 192.168.0.42 xmlp05100d.bin primary all copy tftp lp 192.168.0.42 xmlb05100a.bin monitor all copy tftp lp 192.168.0.42 xmlprm05100a.bin boot all copy tftp mbridge 192.168.0.42 mbridge_05100d.xsvf copy tftp lp 192.168.0.42 lpfpga05100d.bin fpga-all all copy tftp lp 192.168.0.42 lpfpga05100d.bin fpga-all all force-overwrite ----------------------------------------- To sync the line cards to the supervisor ----------------------------------------- lp boot system flash primary 1 lp boot system mp primary 1 copy running-config #show flash #reload-check #(config)enable super-user-password #lp cont-boot sync 1 #lp cont-boot sync 2 -------------------- After it comes back --------------------- Configure management user combined image - xm05100c.bin #copy tftp image 192.168.0.24 xm05100c.bin del #copy tftp image 192.168.0.24 xm05100c.bin lp-sec del #copy tftp image 192.168.0.24 xm05100c.bin mp-sec del #copy tftp image 192.168.0.24 xm05100c.bin secondary del #reload-check --------------- Troubleshooting --------------- #Config t #lp boot system interactive [slot#] #exit #wr mem #Power-off lp [slot#] #Power-on lp [slot#] #lp 1 boot system-interactive ` #(config)module ------------------------------------------------------------------------------------ ------------------------------------------------------------------------------------ Brocade BigIron RX-4 ------------------------------------------------------------------------------------ ------------------------------------------------------------------------------------ #copy tftp image 192.168.0.24 rx02800a.bin #copy tftp flash 192.168.0.24 rmpr02800a.bin secondary #copy tftp lp 192.168.0.24 rlp02800a.bin primary all #copy tftp lp 192.168.0.24 rlp02800a.bin secondary all ------------------------------------------------------------------------------------ ------------------------------------------------------------------------------------ EdgeIron 48G ------------------------------------------------------------------------------------ ------------------------------------------------------------------------------------ Password recovery: Press CTRL+U Type password "mercury" Press "D" Delete Factory_Default_Config.cfg Press "Q" to boot Upgrade: ----------------------------------- Loader(boot Code) - EIFG_bv2301.bin Image - EIFG_v22733.bin Diagnostic Code - EIFG_dv2200.bin (config)#boot system opcode: EIFG_v22733.bin (config)#boot system boot-rom EIFG_bv2301.bin --------------------------------------------------------------------------- --------------------------------------------------------------------------- ServerIron100 or 400 --------------------------------------------------------------------------- --------------------------------------------------------------------------- 1. Copy the MP boot code copy tftp flash boot 2. Copy the WSM CPU boot code wsm copy tftp flash boot 3. Copy the WSM CPU flash code wsm copy tftp flash primary 4. Copy the MP flash code 5. Reload 6. Copy the MP flash code While the device is still rebooting, press the “b” key to enter the Boot PROM. You may need to hold the key down for a few seconds. The Boot PROM has the following prompt: BOOT MONITOR> At the Boot PROM prompt, enter the following commands to reboot the device from the TFTP server, using the new MP flash code you copied onto the server: ip address boot system tftp 7. copy tftp flash primary ------------------------------------------------------------------------------------ ------------------------------------------------------------------------------------ Fast Iron Edge X448 ------------------------------------------------------------------------------------ ------------------------------------------------------------------------------------ configure 4 SPF ports FastIron(config)# interface ethernet 1 to 4 FastIron(config-mif-1-4)# gig-default auto-gig ---------------------------------------------------------------------------------- ------------------------------------------------------------------------------------ ServerIronGT EGC16 ---------------------------------------------------------------------------------- ------------------------------------------------------------------------------------ boot tftp x.x.x.x wsm boot tftp x.x.x.x wsm copy tftp fla 192.168.0.35 wsp-b54.bin boot "disable stand" then "enable mod 2" ------------------------------------ Tue, 24 Feb 2009 05:53:02 -0800 Have you checked the output of "show ru" - do you see "wsm boot int" in the configuration? If so: remove it!!! It looks like you are doing an upgrade from a very old code. You do need to boot the BP in interactive mode initially to get the runtime image to the BP. The upgrade process would look like: copy tftp flash a.b.c.d BOOT-imageMP boot copy tftp flash a.b.c.d imageMP.img pri wsm copy tftp flash a.b.c.d BOOT-imageBP boot conf t wsm boot int boot sys flash pri wr mem exit reload WAIT UNTIL IT IS UP wsm boot tftp a.b.c.d imageBP.img WAIT UNTIL BP IS UP wsm copy tffp flash a.b.c.d imageBP.img pri conf t wsm boot pri wr mem exit reload ------------------------------------------------------------------------------------ ------------------------------------------------------------------------------------ Juniper M10i ------------------------------------------------------------------------------------ ------------------------------------------------------------------------------------ #show chassis fpc pic-status #show chassis alarms #show chassis hardware detail #request chassis pic fpc-slot 0 pic-slot 0 online #show chassis fpc pic-status 1 ------------------------------------------------------------------------------------ ------------------------------------------------------------------------------------ Juniper M7i ------------------------------------------------------------------------------------ ------------------------------------------------------------------------------------ #show chassis alarms #show system boot-messages #set system root-authentication plain-text-password #show chassis environment #show interfaces brief #set system root-authentication plain-text-password #set chassis alarm management-ethernet link-down ignore #interop@J4300# edit int fe-0/0/1 #interop@J4300# set unit 0 family inet address 172.28.20.254/24 #delete interfaces ge-0/0/3 unit 0 family ethernet-switching vlan members sales ------------------------------------------ ------------------------------------------ Juniper 4300 and 3200 ------------------------------------------ ------------------------------------------ root# edit interfaces xe-0/1/0.0 root# delete family ethernet-switching root# set family inet address 192.168.0.77/24 root# commit ---------------------------------------------------------------------------------- ------------------------------------------------------------------------------------ Juniper SRX650 ---------------------------------------------------------------------------------- ------------------------------------------------------------------------------------ switch> request system configuration rescue save switch> request system zeroize switch> request system halt ------------------------------------------------------------------------------------ ------------------------------------------------------------------------------------ Junos commands ------------------------------------------------------------------------------------ ------------------------------------------------------------------------------------ http://www.slideshare.net/haobin/junipertroubleshooting --------------------------------------------------------------------------------- ------------------------------------------------------------------------------------ Netgear ---------------------------------------------------------------------------------- ------------------------------------------------------------------------------------ show network show port all show inventory show stats port detailed network parms network protocol none network parms 192.168.0.2 255.255.255.0 192.168.0.1